铝塑复合门窗

News

product

contact

Name: Liaoning Super Group Construction Group Co., Ltd.

Super group hardware accessories store:

0417-5860985 2110985

Doors and windows, stretch bending and pressboard workshop:

0417-5950999

Address: middle section of South outer ring of Dashiqiao
E-mail:cnzs-168@163.com
Website:www.zs-china.com

Construction preparation of white steel doors and windows

Your current location: Home >> News >> Technology Center

Construction preparation of white steel doors and windows

Date:2015-05-13 Author: Click:

三、

 

安装施工准备

 

1

 

材料要求

 

白钢门窗产品及材料应符合以下要求:

 

1

 

白钢门窗的规格、型号、和五金配件及玻璃应符合设计(业主)要求和相关

标准要求,并具有出厂合格证,一般无特殊情况下,门、窗的白钢型材壁厚

不小于

1.2mm

 

2

 

白钢门窗料表面阳极氧化膜质量符合设计标准的规定,应达到

AA10

级以上

(平均厚度不小于

10um

 

3

 

公共出入口处的白钢门必须采用安全玻璃。

 

4

 

五金附件应符合国家或相应标准的规定,露出的零部件应采用不锈钢或经镀

锌处理。

 

5

 

橡胶条、毛刷条、密封胶以及玻璃等的质量应符合国家或相关标准的规定。

 

6

 

白钢窗框下槛应开设泄水孔,

其位置和数量应保证雨天下槛排水通畅不积水。

 

7

 

白钢门窗框侧边不准随意钻孔,孔洞应用铜帽或塑料帽覆盖,并在洞口处用

密封胶密封,铝合金门窗型材拼接处、紧固螺栓孔也应用密封胶密封。

 

2

 

机具设备

 

切割机、电焊机、冲击电钻、电锤、手枪钻、射钉枪、经纬仪、螺丝刀、锉

刀、手锤、扳手、粉线包、钢卷尺、钢直尺、钢板尺、铁锹、水桶等。

Installation and construction preparation 1. Material requirements White steel doors and windows products and materials should meet the following requirements: (1) White steel doors and windows specifications, models, and hardware accessories and glass should meet the design (owner) requirements and related standards, and has a factory certificate of conformity, in general no special circumstances, the door, window wall thickness of white steel profiles Not less than 1.2mm. (2) The quality of anodic oxide film on the surface of white steel doors and windows meets the requirements of design standards and should reach AA10 grade or above (average thickness is not less than 10um). (3) safety glass must be used at the gate of public entrance and exit. (4) Hardware accessories shall meet the requirements of the state or the corresponding standards, and exposed parts shall be made of stainless steel or galvanized. (5) The quality of rubber strips, brush strips, sealants and glasses shall meet the requirements of the state or relevant standards. (6) The bottom sill of the white steel window frame should be provided with drainage holes, and the location and quantity of the holes should ensure that the sill drainage in rainy days is smooth and does not accumulate water. (7) White steel doors and windows are not allowed to drill holes at will. The holes are covered with copper caps or plastic caps and sealed with sealant at the entrance of the holes. Sealant seals are also used at the joint of aluminum alloy doors and windows and fastening bolt holes. 2. Cutting machine, welding machine, percussive electric drill, hammer, pistol drill, nail gun, theodolite, screwdriver, file, hammer, wrench, powder package, steel tape, steel ruler, steel plate ruler, shovel, bucket, etc.

Tags:白钢门窗

Browse:

Share